What is fabric pretreatment

Fabric pretreatment is the set of steps before dyeing used to remove or modify residues on greige fabric that could interfere with dyeing — loose fibres, warp sizing, oils and natural colouring matter — so the fabric absorbs water and dye evenly. The preparation route depends on fabric type and end use. Woven greige fabric often carries warp size and other production residues, so it usually needs preparation before dyeing: the warp yarns carry a sizing (starch or a synthetic) applied before weaving to reduce yarn breakage and improve weaving efficiency (CBSE), and cotton carries natural impurities and oils on top of that. When present, warp sizing is removed during preparation, along with oils and impurities that could interfere with dyeing. If size or other impurities remain, they can affect dye penetration and shade uniformity.

What each step does

Singeing

Singeing removes protruding fibre ends from the yarn surface, leaving a cleaner, lower-fuzz face. CBSE notes that fabric passes the flame quickly to avoid scorching and that uneven singeing can lead to uneven dyeing.

Desizing

Desizing removes sizing from woven fabric when it is present. Sizing helps reduce yarn breakage and improve weaving efficiency (CBSE); residual size can interfere with dyeing and printing, so the route is confirmed against the actual fabric. The method depends on the size: amylase enzymes are used to remove starch-based sizing, while other size chemistries may require a different treatment (CBSE; Scientific Reports, 2023).

Scouring

For cotton, scouring is a cleaning treatment to remove oils, waxes and residues that can interfere with absorbency. The CBSE Textile Design curriculum describes a hot alkaline bath, such as sodium hydroxide; the exact chemistry and conditions depend on the fibre and process.

Bleaching

Bleaching uses an oxidising agent, such as hydrogen peroxide (H2O2), to remove natural colouring matter and create a whiter base when a bright or pale shade is required (CBSE). The exact treatment depends on the fibre and process.

Woven vs knitted: does every step apply?

No — CBSE states that not all pretreatment operations are used on every fabric; it depends on the fabric type and the end use:

  • Wovens: warp yarns may carry sizing, so check the fabric before deciding whether desizing is needed (CBSE).
  • Weft knits: they do not have woven warp yarns carrying loom size; check construction and residues before deciding whether desizing is needed (NC State; CBSE).
  • Cotton and cotton blends: scouring is used where natural oils, waxes and residues need removal (CBSE).
  • White or pale colours: bleaching may be used to create a whiter base; confirm the process against the shade and fabric.
  • Deep colours: a full bleach may not be needed; the route depends on the fabric and end use.
  • Singeing: may be considered when a lower-fuzz surface is required (CBSE).

What buyers should tell the dyehouse

When ordering dyeing or bleaching, this is what lets the mill pick the right route:

  • Colour target — bright or pale shades may need a whiter base than deep shades.
  • Surface target — discuss singeing if reducing protruding fibres and fuzz is important.
  • Fabric type and fibre — woven or knitted, cotton, TC, TR, polyester or blends affect the desizing route.
  • End use and buyer-required standards — for example, uniforms or hospital cloth, to select tests.

The exact sequence is the dyehouse's call against the fabric spec — minimum orders are negotiable.

How BCI handles pretreatment

BCI (Boonchuay Industrial) is a commission dyeing and finishing house with over 60 years of experience, at Sam Phran, Nakhon Pathom. The flow from greige to finished roll:

  • Greige inspection — faults marked before any chemical is used
  • Lab dip — colour matched and approved by the customer first
  • Pretreatment as required by the fabric and specification — singeing, desizing when size is present, scouring, bleaching (and mercerising where needed)
  • Dyeing — to the approved standard, with in-process checks
  • Finishing — calendering, sanforizing, mercerizing, brushing, raising, shearing, air tumbling
  • Final inspection and roll-up

Quality follows three checkpoints: greige inspection before dyeing, in-process control and inspection at packing. BCI provides a 10-point system quality report for every lot. The in-house laboratory tests to ISO, JIS, AATCC and Daimaru standards.

How to judge the result

  • Shade uniformity — no streaks or spots left by residual sizing
  • Colour fastness — to the standard in the spec: washing (ISO 105-C06), rubbing (ISO 105-X12), light (ISO 105-B02, blue wool 1–8)
  • Surface — clean, low fuzz, lustre as specified
  • Whiteness — for white or pale goods

FAQ

What happens if the sizing is not fully removed? Residual size can affect dye uptake and shade uniformity (CBSE; Scientific Reports, 2023). Residual size can also interfere with later wet-processing steps such as printing (CBSE; Scientific Reports, 2023). Do knitted fabrics need desizing? It depends on construction and any residual size. Weft knits do not use the woven warp yarns that normally carry loom sizing; ask the dyehouse to confirm the route for the exact fabric (NC State; CBSE). Do deep colours need a full bleach? Not necessarily — a deep colour needs a clean, even base, not a fully white one. A whiter base may be needed for white or pale colours; confirm the route against the fabric and shade. What does singeing do? It removes protruding fibres; the fabric must pass quickly enough to avoid scorching, with the speed and flame set for the cloth (CBSE). Does BCI only take dyeing work, or bleaching and pretreatment too? BCI's fabric-dyeing page describes a route from pretreatment through dyeing and finishing. Send the fabric specification to the BCI team to confirm whether a pretreatment-only order fits. How do you know the pretreatment was done well? Look at shade uniformity, fastness to the standards in the spec, and the surface. BCI provides a 10-point system quality report for every lot.

Talk to BCI

BCI (Boonchuay Industrial) is a commission dyeing and finishing house with over 60 years of experience at Sam Phran, Nakhon Pathom. Pretreatment is part of the full fabric dyeing and finishing service — from greige inspection through dyeing and finishing to the rolled, finished cloth. If you have greige fabric that needs preparing, dyeing, or both, send the fabric specification and a colour reference to the BCI team to confirm the process route, quantity and process requirements for your job — see contact the BCI team.

References